ACTAS P360 / ACTAS P260

Portable Switchgear Test Systems

Flexible and compact test systems for carrying out tests on medium-, high- and extra-high-voltage switchgear.

  • Extremely robust and compact
  • Full switchgear test in a single test procedure
  • No need for time-consuming reconnection during tests
  • Stand-alone operation
  • Operation and evaluation via 7" touch screen
  • PIR and main contact measurement on up to 12 main contact chambers
  • Recording and analysis of coil and motor current
  • Status of up to 12 auxiliary contacts
  • Coil current measurement on up to three closing and opening coils
  • 9 analog/digital sensors for pressure, travel and temperature measurement
  • 3 voltage measurement inputs
  • Static/dynamic resistance determination on up to 6 main contact chambers with PROMET SE
  • Determination of operating times with earthing on both sides on up to 6 main contact chambers with PROMET SE

Comprehensive on-site switchgear testing

Using the integrated control panel of ACTAS P260 | P360, it is possible to carry out complete tests on medium-, high- and extra-high-voltage switchgear. Analysis can be performed quickly, easily, automatically and with a high degree of flexibility within a single test procedure using the following measurements:

The test fulfils all the requirements stipulated in IEC 62271-100 for assessing the mechanical behaviour of high-voltage circuit breakers.

Contact travel visualization

Unlike evaluation based on a simple binary signal, as is used in high-frequency measuring methods, ACTAS P260 | P360 test systems used in combination with the compact PROMET SE ohm meter enable a sound diagnosis of interrupter units throughout the whole switching operation. Measurement results are displayed in curve form. This allows an accurate assessment of the start of travel and the final position of the contacts and even reveals time differences between the movements of the main and resistive contacts.

Assessing the interrupter unit by analysing contact resistance

Regular measurements of the static and dynamic contact resistance allow an accurate assessment of the condition of the entire contact system. This ensures that maintenance requirements can be identified at an early stage and down times kept to a minimum. Using three PROMET SE ohm meters and the CSW3 connection unit, contact resistance measurements can be carried out on up to 6 main contact chambers and can be incorporated within the test procedure. The test current can be set to a maximum of 200 A. Even very low resistance values in the single-digit micro-ohm range can be measured extremely accurately. The measured values are used for the evaluation of tests and are included in the test report.

Static and dynamic measurement

A high contact resistance within a switchgear device leads to high power loss coupled with thermal stress which can potentially cause serious damage to the switchgear device. Problems, such as high transfer resistance resulting from poor connections, can be identified by measuring static contact resistance. Dynamic contact resistance measurements can be used to determine the resistance characteristic during a freely definable switching operation. Measurements of this type give an indication of the length and state of the arcing contacts of high-voltage breakers, for example.

Testing with earthing on both sides

Switchgear equipment is often tested with earthing on both sides in order to prevent danger caused by capacitively coupled voltages from neighbouring components. However, when switchgear equipment is tested using conventional measuring methods, earthing must be removed on at least one side. When tests are carried out in combination with PROMET SE, measurements can be carried out with earthing on both sides. Not only does this make tests much safer, it also makes them simpler and quicker because all the steps which need to be taken in order to remove the earth lead are no longer required.

Motor and coil tests

The ability to connect a powerful AC/DC source makes it possible to test the correct functioning of motors and coils of switchgear devices directly and independently of the station voltage. Analyses of motor and coil operation, through the determination of the minimum operating voltage and through testing undervoltage releases for coils, for example, are reproducible and can always be carried out under identical conditions.

Integrated operating and evaluation unit

The resistive 7“ touch screen, a new operating concept and extra powerful hardware make for easy operation and optimum display of all information.

The clear, well-structured user interface is self-explanatory and guides the user quickly and intuitively to complete the task in hand. All test parameters are displayed clearly and can be set directly. The measurement results are shown on the display together with the associated signatures enabling conclusions to be drawn directly as to the state of the switchgear device. A test report can be produced in PDF format to document the test.

Example test results

Remote control over Wi-Fi

Because ACTAS P260 I P360 can be controlled with a smart phone, or tablet etc., the test instrument can also be operated from some distance away. This allows the stipulated minimum distance to be observed when carrying out first trip measurements, for example.

ACTAS testing software

Configuration and analysis of tests are carried out with the ACTAS testing software and the control panel located on the test system itself. The expertise which has gone into the development of the testing software results from more than 20 years of experience in developing and manufacturing switchgear test systems and from close cooperation with network operators and switchgear manufacturers.
It is easy for tests to be called up, edited or used as templates. A graph of all measured signal characteristics, featuring zoom functions and measurement cursors, offers a  wide variety options for detailed analysis.
Test analysis and test management can also be carried out with a PC. Test data can be imported or exported with a USB flash drive or a network connection.

Result help

The ACTAS testing software features a comprehensive help function to support users in the selection and evaluation of the measurement results. Descriptions and graphs facilitate the correct interpretation of the results obtained.

Automatic generation of test reports

The software includes an option for automatically creating test reports to document test results. As well as the results themselves, reports also include curve characteristics of recorded signals, switchgear data and test parameters.

Compact, robust and reliable

ACTAS P260 | P360 are compact, robust test systems which are specially designed for portable use and come in a practical hard-top case. During the development process, special attention was paid to their ability to withstand harsh transport and operational conditions.
The use of tried and tested hardware components and the very high electromagnetic compatibility of the test systems ensure that they function reliably, even in extra-high-voltage environments.

PROMET SE ohm meter

PROMET SE is a compact, battery-operated ohm meter with an adjustable test current of up to 200 A. Two current outputs and two voltage measurement inputs allow the resistance to be determined at two measurement points simultaneously. Because the device weighs just 1.5 kg and features a compact housing fitted with a carrying strap, it can even be used in situations where it cannot be put down, for example when working on ladders or hoisting platforms.

PROMET SE
Measuring lead
Measuring lead
Screw clamp
Screw clamp
Test clamp for main contacts
Test clamp for main contacts
Terminal adapter
Terminal adapter
Main contact cable
Main contact cable
Auxiliary contact cable
Auxiliary contact cable
Voltage measurement cable
Voltage measurement cable
Coil cable
Coil cable
Current measurement cable
Current measurement cable
P360P260
Operating voltage110…265 VAC/DC
Control outputs for
closing coils
31
Control outputs for
opening coils
31
Main and PIR contacts6 x 23 x 2
Coil current3 x 2 (I / O)1 x 2 (I / O)
Coil / motor /
station voltage
31
Motor current via shunt11
Sensor
(+  / – 10 V  /  digital)
63
Sensor
(+  / – 10 V / 0…20 mA)
31
Auxiliary contacts3 x 42 x 4
Reference voltage for sensors
10 VDC  / 200  mA
31
PC connection1 x Ethernet
Interfaces1 x USB A  /  1 x USB B
Interfaces for external devices3 x RJ45 for PROMET SE
1 x RJ45 for CSW3
User interface7" graphical display with touch screen and 2 function keys
HousingRobust hard-top case
Protection classIP65 (closed)
Dimensions (mm)475 x 375 x 180424 x 340 x 173
Weight (kg)6.95.3


Technical specifications subject to change without prior notice